Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
dubbing_station_guide_-_vcr [2011/07/19 10:05] 127.0.0.1 external edit |
dubbing_station_guide_-_vcr [2022/12/04 23:34] rosterberg removed |
||
---|---|---|---|
Line 3: | Line 3: | ||
===Dubbing Station Guide - VCR=== | ===Dubbing Station Guide - VCR=== | ||
- | The following document will go over use the dubbing station that can be used for editing DVD media. For further assistance, contact the Help Desk (help.desk@olin.edu or x. 2430). | + | The following document will go over use the dubbing station that can be used for editing DVD media. For further assistance, contact the Help Desk (helpdesk@olin.edu or x. 2430). |
**The Players:** | **The Players:** | ||
Line 13: | Line 13: | ||
* SOURCE -> JVC SR-V530 (NOTE: REMOTE LABELED AS **VCRS**) | * SOURCE -> JVC SR-V530 (NOTE: REMOTE LABELED AS **VCRS**) | ||
* DESINATION -> Panasonic – AG-2580P (NOTE: REMOTE LABELED AS **VCRD**) | * DESINATION -> Panasonic – AG-2580P (NOTE: REMOTE LABELED AS **VCRD**) | ||
- | * | + | |
:!: It is recommended that you do not use the remotes. They are available but both VCR's receive signals at the same frequency. | :!: It is recommended that you do not use the remotes. They are available but both VCR's receive signals at the same frequency. | ||
**Directions for Dubbing:** | **Directions for Dubbing:** | ||
- | - Make sure the RCA cables labeled VCR are connected to the TV Set (see image below) | + | |
+ | * Make sure the RCA cables labeled VCR are connected to the TV Set (see image below) | ||
:!: Use **Y** 2 to 1 connector. | :!: Use **Y** 2 to 1 connector. | ||
- | {{:it:av_jacks.jpg|}} | + | {{av_jacks.jpg|}} |
+ | -Turn on TV and tune it to Line Input. | ||
+ | -Turn on Source and Destination VCR players. Place the VHS or DV tape to be copied into the Source player, and your blank VHS into the Destination player. | ||
+ | -Using the Destination VCR, press the Channel buttons (located under the VHS bay) until you reach the L-1 input. | ||
+ | -Using the Source VCR player, find the point on the VHS or DV tape from which you wish to begin copying. | ||
+ | -Once you are ready to record, press record on the Destination VCR player, then press play on the Source VCR player. | ||
+ | -When finished recording, press stop on both players. | ||
+ | -Repeat the editing process until you are finished. (To copy multiple clips, repeat 5-7 until finished) | ||
- | - Turn on TV and tune it to Line Input. | ||
- | - Turn on Source and Destination VCR players. Place the VHS or DV tape to be copied into the Source player, and your blank VHS into the Destination player. | ||
- | - Using the Destination VCR, press the Channel buttons (located under the VHS bay) until you reach the L-1 input. | ||
- | - Using the Source VCR player, find the point on the VHS or DV tape from which you wish to begin copying. | ||
- | - Once you are ready to record, press record on the Destination VCR player, then press play on the Source VCR player. | ||
- | - When finished recording, press stop on both players. | ||
- | - Repeat the editing process until you are finished. (To copy multiple clips, repeat 5-7 until finished) |